Share

Back to overview

E-MTB TERMINOLOGY EXPLAINED

Get acquainted with E-MTB terminology, care of this handy primer.

Even those of us who speak fluent bike, who know their SLX from their XTR, and their stack from their reach, might not yet be proficient in the language of E-MTBs.

The technology that drives E-bikes arrived so quickly that even those of us who can see at a glance how much a bike should cost, what it should weigh, and how to service its parts may be a bit hesitant when it comes to assessing a new generation of E-parts. Here’s a primer on the language of E-MTB, in alphabetical order.

AMP-HOURS

Amp-hours (Ah) are a measure of battery capacity—so the more Amp-hours on offer, the longer each charge cycle will last. Good quality E-MTB batteries offer between 11 and 14Ah.

CHARGE CYCLE

An emptying and refilling of the battery. Projected battery life is usually expressed in terms of charge cycles, so a battery with 1,000 charge cycles should last through 1,000 recharges. While there’s some decrease in capacity over this time, 1,000 charge cycles would usually be enough for years of use.

HUB MOTOR

Describes any kind of E-bike where motor sits inside a hub, often in the rear wheel.

LITHIUM-ION BATTERY

There are many different batteries available for E-MTBs, but Lithium ion (or Li-ion) batteries are typically the best-performing, being light, and with a long lifespan. Lithium-ion batteries are used in a wide range of rechargeable devices, including mobile phones and cameras. 

MID-DRIVE MOTOR

Sometimes called a bottom bracket motor, this motor is located centrally in the bottom bracket, as opposed to in the hub. This is becoming a popular choice for E-MTBs as it provides low, centered weight distribution, intuitive ride feel, and easy wheel removal compared with hub motors.

MODE A

Level of motorized support provided by a pedal assist E-MTB, selected by the rider using a handlebar-mounted switch and displayed via a unit mounted to handlebars. Shimano STEPS E8000, for example, offers three drive modes: Eco, Trail, and Boost.

NEWTON METER (NM)

A measure of torque, force that is applied to cause rotation (see Torque).

PEDAL-ASSIST

Pedal-assist E-bikes sense the torque or cadence of the rider and respond by increasing power output. They differ from throttle-powered E-bikes, which operate more like mopeds, and do not require pedaling. Pedal-assist E-MTBs have a natural ride feel, are legally classified as bicycles in most countries, and are the most common type of E-MTBs produced by major bicycle manufacturers.

POWER

Measured in Watts (W), this is the amount of work that can be done by the E-bike system. Most pedal-assist E-bikes sold in Australia are limited to between 200 and 250W by law. The more watts, the more powerful the system is. One Horsepower is 750W (see Watt).

Q FACTOR

Put simply, the distance between the pedals measured parallel to the bottom bracket. On mid-drive E-bikes and E-MTBs, Q factor has, in the past, been wider to accommodate motors. Now, systems such as Shimano STEPS offer the same Q factor as standard mountain bikes.

RANGE

The distance or time a battery will last under any given circumstances. Range is determined by battery capacity, and affected by the total weight of bike and rider, the terrain (hilly, flat, downhill), and ride mode. Range changes according to these circumstances, and is usually dynamically displayed on a handlebar-mounted computer.

SUPPORT RATIO

In pedal-assist E-MTBs, the percentage of a rider’s pedaling input that is provided by the motor. This changes at different modes. For example, a low mode might support 70% of a rider’s pedaling power, while a high mode might support over 250%. Batteries last longer at lower support ratios.

TORQUE

Measured in Newton meters (Nm), torque is a measure of force applied to cause rotation. Torque specifications for E-MTBs (for example, 70Nm) refer to the maximum force that can be applied to the rear wheel by the motor.

VOLTAGE

In simple terms, this refers potential force of power flow from battery to motor, similar to the way water runs through a hose under pressure.

WALK MODE

A low-power mode to assist with walking the bike on stairs and around tight corners, for example.

WATT

An important unit of measurement of power produced by a system and, along with voltage, determines how fast an E-MTB can go.

WATT-HOURS

A measure of overall battery capacity found by multiplying Amp-hours by voltage (then rounded to the nearest 50 or so). So, a battery with a rated voltage of 36V and 14Ah is said to have a capacity of 500Wh (36x14=504).

Related article